Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Ultramid® B3WG6 GPX BK23238 - PA6-GF30 - BASF

Check here, which other Ultramid B datasheets, application examples or technical articles are available in Material Data Center

Processing/Physical Characteristics - Mechanical properties - Thermal properties - Electrical properties - Other properties - Material specific properties - Processing Recommendation Injection Molding - Diagrams

Any use of this information falls under the rules of our disclaimer.

Product Texts

Glass fibre reinforced and heat ageing resistant injection moulding grade for primary use in plastic air intake manifolds.
This grade has been engineered to provide excellent long-term burst strength retention.

Processing/Physical Characteristics	dry / cond	Unit	Test Standard
ISO Data
Melt volume-flow rate, MVR	20 / *	cm³/10min	ISO 1133
Temperature	275 / *	°C	-
Load	5 / *	kg	-
Molding shrinkage, parallel	0.3 / *	%	ISO 294-4, 2577
Molding shrinkage, normal	0.6 / *	%	ISO 294-4, 2577

Mechanical properties	dry / cond	Unit	Test Standard
ISO Data
Tensile Modulus	9800 / 5400	MPa	ISO 527
Stress at break	185 / 110	MPa	ISO 527
Strain at break	3.5 / 8	%	ISO 527
Tensile creep modulus, 1000h	* / 4100	MPa	ISO 899-1
Charpy impact strength, +23°C	95 / 105	kJ/m²	ISO 179/1eU
Charpy impact strength, -30°C	85 / 95	kJ/m²	ISO 179/1eU
Charpy notched impact strength, +23°C	13 / 22	kJ/m²	ISO 179/1eA
Charpy notched impact strength, -30°C	10 / 11	kJ/m²	ISO 179/1eA

Thermal properties	dry / cond	Unit	Test Standard
ISO Data
Melting temperature, 10°C/min	220 / *	°C	ISO 11357-1/-3
Temp. of deflection under load, 1.80 MPa	200 / *	°C	ISO 75-1/-2
Temp. of deflection under load, 0.45 MPa	220 / *	°C	ISO 75-1/-2

Electrical properties	dry / cond	Unit	Test Standard
ISO Data
Relative permittivity, 100Hz	4.6 / 33.4	-	IEC 62631-2-1
Relative permittivity, 1MHz	4.1 / 5.4	-	IEC 62631-2-1
Dissipation factor, 100Hz	126 / 8930	E-4	IEC 62631-2-1
Dissipation factor, 1MHz	201 / 1340	E-4	IEC 62631-2-1
Volume resistivity	1.1E9 / 1.3E8	Ohm*m	IEC 62631-3-1
Surface resistivity	* / 5.2E12	Ohm	IEC 62631-3-2
Electric strength	47 / 29	kV/mm	IEC 60243-1
Comparative tracking index	375 / 375	-	IEC 60112

Other properties	dry / cond	Unit	Test Standard
Water absorption	6.6 / *	%	Sim. to ISO 62
Humidity absorption	2.35 / *	%	Sim. to ISO 62
Density	1350 / -	kg/m³	ISO 1183

Material specific properties	dry / cond	Unit	Test Standard
ISO Data
Viscosity number	150 / *	cm³/g	ISO 307, 1157, 1628

Processing Recommendation Injection Molding	Value	Unit	Test Standard
Pre-drying - Temperature	80	°C	-
Pre-drying - Time	4	h	-
Processing humidity	≤0.15	%	-
Melt temperature	270 - 290	°C	-
Mold temperature	80 - 90	°C	-

Diagrams

Characteristics

Processing

Injection Molding

Delivery form

Black

Regional Availability

North America, Europe, Asia Pacific, South and Central America, Near East/Africa

Other text information

Injection molding

PREPROCESSING
Pre/Post-processing, max. allowed water content: .15 %
Pre/Post-processing, Pre-drying, Temperature: 80 °C
Pre/Post-processing, Pre-drying, Time: 4 h

PROCESSING
injection molding, Melt temperature, range: 270 - 290 °C
injection molding, Melt temperature, recommended: 280 °C
injection molding, Mold temperature, range: 80 - 90 °C
injection molding, Mold temperature, recommended: 80 °C
injection molding, Dwell time, thermoplastics: 10 min

Disclaimer

Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.

Created: Source: www.materialdatacenter.com

Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.